104 reviews for Aluminum Front Truck Racks – Black

1. AdminDeeZee2 – December 7, 2017

   Our racks come either a gloss or textured black powder coat. The textured finish is TB at the end of the part number.

2. AdminDeeZee2 – July 16, 2019

   The toolbox would fit just fine.

3. AdminDeeZee2 – January 7, 2020

   We are not sure. We do not test fit the rack with covers. There are too many to do this with. The racks mounting foot has a flange that will come down on the inside edge of the bed rail. This could interfere with the fitment of the cover. Review installation instructions for more information.

4. AdminDeeZee2 – December 19, 2019

   You will want to review the tonneau covers installation to see if it will work in conjunction with the way the cab rack feet sit on inside lip of the bed rail.

5. Rated 4 out of 5

   Brian Fregeau – December 18, 2019

   I have had this rack on my truck for about 7 years. It still looks like brand new. Even in the harsh Canadian climate. The steel racks rust pretty quick around here. The original DeeZee logo decal faded after a few years so I ordered a replacement because the rest of the rack looks so good. I just removed this rack because I’m replacing the truck and I did notice that the rubber mounting hardware nuts appear to have deteriorated quite a bit and will likely need to be replaced in order to mount it on the new truck. If it wasn’t for that this would have been 5 star for sure.

6. AdminDeeZee2 – December 6, 2019

   Not sure. Check the installation instructions for the rack. I uses the top and inner bed rail for mounting purposes.

7. AdminDeeZee2 – November 20, 2019

   You will need to review the installation of the rack to how the tonneau cover installs. The rack feet have a flange that goes on the inside of the bed rail.

8. AdminDeeZee2 – October 28, 2019

   With the corners rounded and the angle of the vertical the measurement is subject. The flat part is approximately 54″.

9. AdminDeeZee2 – October 28, 2019

   Any of our crossover toolboxes will fit with our cab racks.

10. AdminDeeZee2 – October 17, 2019

    It depends on how the cover attaches to the front of the bed. Our cab rack feet uses the inside edge of the rail for installation. Check with the instructions to see if the installation of both will work.

11. AdminDeeZee2 – September 11, 2019

    You will need to check the installation instructions for the cab rack to the cover to see if there is any interference.

12. AdminDeeZee2 – September 11, 2019

    The front racks are only available with the mesh.

13. AdminDeeZee2 – September 11, 2019

    Size of the bed is not the issue. Dodge trucks are different when it comes to the cab height compared to our standard cab rack. Prior to 2009 the the cab rack would fit on a Dodge but when anything was placed on top of the rack it would then touch the top of the cab and the third brake light would not be visible.

14. AdminDeeZee2 – August 21, 2019

    Review the installation instructions with how the cover is installed at the front of the truck bed. The cab rack mounting plate has a flange that comes down on the inside of the bed rail.

15. AdminDeeZee2 – July 9, 2019

    Unfortunately we do not have an image of the rack on that specific model truck.

16. AdminDeeZee2 – February 17, 2020

    Sorry for the confusion. The hardware does come with the rack. Should anything be missing contact our customer service for assistance. 800-779-2102

17. AdminDeeZee2 – June 18, 2019

    It may extend a little beyond the mounting plate of the cab rack. It would not be much of an issue.

18. AdminDeeZee2 – June 18, 2019

    Suggest looking at the installation to see if the way the cover and the rack install will be compatible. There is a flange on the rack mounting plate that goes down the inside edge of the bed rail which may affect the fitment of the cover.

19. AdminDeeZee2 – May 23, 2019

    Our standard toolbox that measures 69.75″ will fit with the cab rack.

20. AdminDeeZee2 – May 23, 2019

    Not sure what a saddlebox is for sure. Any standard crossover toolbox will fit with the cab rack.

21. AdminDeeZee2 – May 15, 2019

    Cab rack will not work with the Ram box if the mounting feet cover the storage lid for the rambox. Working with the tonneau is questionable due to how some mount at the front of the bed. Review installation instructions to see the rack will work with the cover.

22. AdminDeeZee2 – May 9, 2019

    Yes. The same rack for GM 73-19 will work on a 73-19 F150.

23. AdminDeeZee2 – May 9, 2019

    The cab rack sits on the bed rail and the feet do go down on the inside of the bed rail for installation. Review the instructions to see if there will be any interference with your cover.

24. AdminDeeZee2 – May 9, 2019

    Yes. The DZ95050RTB and DZ95054RTB will work on the 19 2500HD Silverado. Those trucks did not change from 18.

25. AdminDeeZee2 – May 9, 2019

    I suggest looking at the installation of the cab rack and compare it to the cover you have. The rack uses the inside edge of the bed rail for installation which may interfere with the tonneau covers installation.

26. AdminDeeZee2 – April 29, 2019

    Unfortunately we are unable to get the rack without the mesh on the front. We receive them already complete and packaged.

27. AdminDeeZee2 – April 29, 2019

    Yes. All of our crossover toolboxes will work with the cab racks.

28. AdminDeeZee2 – April 12, 2019

    Yes. Our standard single lid crossover will fit.

29. AdminDeeZee2 – March 19, 2019

    There is a strong possibility that it will limit the range of camera coverage.

30. AdminDeeZee2 – January 7, 2020

    We do not have lights that fit in those holes. The hole size is length 2.559″ x .866″.

31. AdminDeeZee2 – February 17, 2020

    No. The racks mounting feet use the inner truck bed rail for installation. This will affect the attachment of the cover.

32. AdminDeeZee2 – January 29, 2019

    From pickup bed to the top of the rack is 23.158″. For fitment with fold up cover will probably not fit. The racks feet that are used to mount to the bed rail has a flange that goes down on the inside edge of the bed rail and will affect the fitment. For more clarification check the installation instructions for DZ95050R. All aluminum racks will use this mounting.

33. AdminDeeZee2 – December 1, 2020

    It does not block the third brake light. But it will affect the camera view.

34. AdminDeeZee2 – February 26, 2021

    A standard crossover toolbox that measures 69.75″ will fit with the Cab Rack.

35. AdminDeeZee2 – January 14, 2021

    81″ is the shipping length of the box.

36. AdminDeeZee2 – December 11, 2020

    No. The rack uses the inside edge of the bed rail for installation.

37. AdminDeeZee2 – November 17, 2020

    the rack is 23.158″.

38. AdminDeeZee2 – February 17, 2020

    Overall Length is 72.596″ and Height is 25.158″.

39. AdminDeeZee2 – November 17, 2020

    Yes it will fit 1500 Denali.

40. AdminDeeZee2 – November 5, 2020

    Not positive that it will. The height from the bed to the top of the rack is 20.89″. It is best to check this dimension to the truck.

41. AdminDeeZee2 – October 29, 2020

    It will not work with OEM cover.

42. AdminDeeZee2 – October 20, 2020

    With the installation of the cab rack, there can be issues with covers. The rack is universal and the mounting plates may not sit tight to all truck beds. The plates also mount using the inside rail of the bed.

43. AdminDeeZee2 – October 20, 2020

    From rail to top is 23.158″.

44. Rated 4 out of 5

    Brayden – June 18, 2020

    I can’t tell if it’s my truck or my install but it’s slightly off and I’m not sure how I can fix it. Instructions were mostly clear, only had to redo one step.

45. AdminDeeZee2 – March 16, 2020

    The height from rail to top of the rack is 23.158″.

46. AdminDeeZee2 – March 9, 2020

    I am not sure what vehicle this rack is for. That is making it hard to answer the question because we have different sizes from standard trucks, to Ford Super Duty, and RAM. Looking at a Super Duty the bottom of the top extrusion would be approximately 24″ from the bed rail. A standard F150 or GM truck the bottom of the extrusion is approximately 20.5″.

47. AdminDeeZee2 – February 25, 2020

    Each truck is a little different but the opening for the third brake will allow it to be visible. There is a chance it could be partially blocked.

48. AdminDeeZee2 – February 25, 2020

    Depending on the vehicle part of the mounting feet may go a little beyond the width of the truck bed.

49. AdminDeeZee2 – February 17, 2020

    The view of the camera may be affected by the cab rack.

50. AdminDeeZee2 – February 17, 2020

    The rack may affect the view of the camera.

51. AdminDeeZee2 – February 17, 2020

    The mounting foot of the cab rack is approximately 5.2″ wide.

52. AdminDeeZee2 – March 19, 2019

    23.185″ is the height from the bed rail to top of rack.

53. AdminDeeZee2 – January 11, 2019

    The width is 72.596″.

54. AdminDeeZee2 – December 7, 2017

    All prices on our website are in US dollar.

55. AdminDeeZee2 – April 24, 2018

    You can contact customer service for that information. 800-779-2102

56. AdminDeeZee2 – April 24, 2018

    The flange on the inside of the bed rail is 1.5″.

57. AdminDeeZee2 – April 23, 2018

    The front silver part number for a 17 F350 is DZ95072R.

58. AdminDeeZee2 – April 18, 2018

    We do not offer a cab rack for the Tacoma.

59. AdminDeeZee2 – March 30, 2018

    Any of our standard crossover toolboxes will fit with the truck racks.

60. AdminDeeZee2 – March 30, 2018

    We do not have a front rack without the mesh. The rears will not work at the front.

61. AdminDeeZee2 – March 8, 2018

    Yes it would.

62. AdminDeeZee2 – March 8, 2018

    Do not have an application for a 93 Toyota pickup.

63. AdminDeeZee2 – March 8, 2018

    23.156″ is the height from bed rail to the top of the rack.

64. AdminDeeZee2 – May 1, 2018

    No. It will not be strong enough with out drilling into the bed rail for mounting.

65. AdminDeeZee2 – February 21, 2018

    The truck bed is a too wide for our standard rack and also it covers the brake light.

66. AdminDeeZee2 – February 21, 2018

    Yes they can.

67. AdminDeeZee2 – February 14, 2018

    We do not have a side rail that will work in conjunction with the rack.

68. AdminDeeZee2 – January 25, 2018

    You can get replacement brackets but they are not adjustable. Same as what comes in the original purchase.

69. AdminDeeZee2 – January 25, 2018

    The mounting plates are 23″ long.

70. AdminDeeZee2 – January 25, 2018

    The racks will not work with most covers. The racks use the inside rail for mounting and that is where most covers are mounted to also.

71. AdminDeeZee2 – January 5, 2018

    Our standard crossover toolbox will fit between the cab rack plates.

72. AdminDeeZee2 – January 5, 2018

    Combined the racks will carry up to 500 lbs. We are unaware of any truck bed covers that will work with our racks with the way they mount on the inside rail.

73. AdminDeeZee2 – December 27, 2017

    The way the rack is packaged for shipping makes it 81″. The overall width of the rack is 72.853″

74. AdminDeeZee2 – December 15, 2017

    Do not have an application for a Hilux.

75. AdminDeeZee2 – December 15, 2017

    Yes. Any toolbox under 70″ will work.

76. AdminDeeZee2 – May 1, 2018

    Call customer service and they will be able to order the parts for you. 800-779-2102

77. AdminDeeZee2 – January 11, 2019

    It depends on how the cover attaches and how that works with the truck bed side rails. The feet on our racks uses the inside edge for mounting.

78. AdminDeeZee2 – July 25, 2018

    Do not know if it works with the bak tonnea or not. It depends on how much area the cover needs for mounting at the front of the pickup bed.

79. AdminDeeZee2 – January 3, 2019

    We don’t offer a spacer kit to raise the rack up. Give a call to customer service to make sure it is the correct rack for your truck. They can look up the dimensions.

80. AdminDeeZee2 – January 3, 2019

    65″ is the safest length to fit.

81. AdminDeeZee2 – January 3, 2019

    We unfortunately do not have light mount brackets for that size of light.

82. AdminDeeZee2 – December 17, 2018

    We suggest looking at the installation instructions for the cab racks to see if it will interfere with where the tonneau cover is mounted. There may be some issues in that area.

83. AdminDeeZee2 – November 28, 2018

    Not sure if it works with that specific cover. Be sure to check the installation instructions to see if there will be interference where the rack mounts on the inside edge of the bed rail.

84. AdminDeeZee2 – September 17, 2018

    From the vertical part of the foot the rack is 72″.

85. AdminDeeZee2 – September 17, 2018

    The Dodge racks will not cross to a GMC. We have separate application part numbers for the Dodge’s because of some differences in height and width of the trucks.

86. AdminDeeZee2 – September 14, 2018

    You will have to check with how the cover mounts and compare to how the rack installs. The rack uses the inside edge of the bedrail for installation.

87. AdminDeeZee2 – August 28, 2018

    We do not custom build the cab racks.

88. AdminDeeZee2 – August 22, 2018

    With so many different covers on the market we cannot test fit the rack with each style. Our rack uses the inside bed rail for installation. For complete information review the instructions.

89. AdminDeeZee2 – August 10, 2018

    It does with some. We don’t know specifically which ones. You will have to compare the installation of the rack and the cover to see if there will be any issues.

90. Rated 5 out of 5

    Britt – August 6, 2018

    The racks are great! I used the headache rack and the rear rack for hauling oversized hauled. Fit and finish is great. The racks were easy to build and even easier to install on the truck.

    Overall great truck bed racks!

91. AdminDeeZee2 – August 1, 2018

    We do not have a non mesh rack that will work on the front and all our front racks come with the mesh. The cover may not work because of the installation of the flange from the cab rack plate. I suggest reviewing the instructions for help in this.

92. AdminDeeZee2 – July 25, 2018

    Overall width is 72.596″ and bracket to bracket is 62.24″. The mesh does not go the top of the box. We have a piece of brite tread that fills that gap with our logo mounted there.

93. AdminDeeZee2 – May 8, 2018

    Flip cover will not work with the cab racks. Cab racks use the inside rail for mounting purposes.

94. AdminDeeZee2 – July 25, 2018

    You will have to see if the flange of the rack will allow the tonneau cover to still be installed at the front of the truck bed.

95. AdminDeeZee2 – July 25, 2018

    Depending on how the cover is attached. The racks do use the inside rail for installation.

96. AdminDeeZee2 – July 2, 2018

    We are only making them in the bolt together design now.

97. AdminDeeZee2 – July 2, 2018

    23.158″ is the height from bed rail to the top.

98. AdminDeeZee2 – June 20, 2018

    Call customer service for assistance on the needed parts. 800-779-2102

99. AdminDeeZee2 – June 20, 2018

    It will close. The measurement is 71.5″

100. AdminDeeZee2 – June 20, 2018

     The width is 72.596″ and the height is 23.158″.

101. AdminDeeZee2 – June 13, 2018

     The flange of the mounting foot that goes down on the inside of the side rail for mounting purposes will make the install of the roll up cover difficult.

102. AdminDeeZee2 – May 23, 2018

     The mounting kits are available. Contact customer service for assistance. 800-779-2102

103. AdminDeeZee2 – May 16, 2018

     You can have them as close or as far apart as you would like. They slide in the cab rack channel.

104. AdminDeeZee2 – May 11, 2018

     They do stick above the cab. They can be used similar to a ladder rack.