Truck Rear Rack, Dee Zee Tough.
You have the front cab rack and are looking to complete the look. Well you can by getting the Dee Zee Aluminum Rear Truck Rack. Now you have a full rack system with endless possibilities. From securing ladders or hauling kayaks to the lake, feel good that they anchored down to arrive at your destination. This will also free up the pickup bed to carry other necessary tools of trade.
Made of 100% 2.75” aluminum tubing with a protective gloss or textured black powder coating, our rear racks are built to handle as much abuse as you can throw at them.
Want to Accessorize? No Problem.
We know truck needs vary from one job to another, that’s why we’ve designed our Rear Rack with an integrated channel system, for endless accessory possibilities. We’ve also made it simple to install by bolting directly into your vehicles existing stake pocket holes.
Dee Zee Rear Racks Feature:
- Rear Truck Rack Gives A Full Rack System
- 2.75" Hexagonal Aluminum Tubing for rugged construction
- 300lb. Limit for One Rack and 500lb. Limit with Two
- Protective Textured or Gloss Black Powder Coat Finish keeps your rack looking fresh
- Integrated Channel System for easy addition of accessories
- Includes Set Of 2 Removable Tie Down Mounts
- Installs into Existing Stake Pocket Holes
- Limited-Lifetime Warranty
Explore Overland Accessories for Midsize Trucks HERE
AdminDeeZee2 –
It will. The only ones that would not cross is on Ford Super Duty trucks. There is a change between 16 to 17.
AdminDeeZee2 –
The rear truck racks will not work on the front. The mounting feet are different.
AdminDeeZee2 –
The rear racks will not mount to the front. Mounting hardware is different. Our racks do work with standard toolboxes with a length of 70″ and under. Length is 72.569″ and Height is 23.158″.
AdminDeeZee2 –
There may be some issues depending on how the cover mounts. Our rack mounts using the inside edge of the truck rail. We suggest reviewing the instructions with the cover to see if they will work together.
AdminDeeZee2 –
The rear non mesh racks mount just a little different and that does not allow them to be installed at the front. the product dimensions are under the additional information tab when looking at a specific part number.
AdminDeeZee2 –
DZ9504RB or DZ95054RTB are the gloss and texture black numbers that will fit on the rear of the pickup bed.
AdminDeeZee2 –
it depends on the installation of the cover. our rack installation feet have a flange that goes done along the inside edge of the bed rail.
AdminDeeZee2 –
It all depends on how the cover attaches and fits at the front bed rail. The cab rack uses the inside edge of the rail for installation.
AdminDeeZee2 –
They will work together. Just need to make sure the lid of the tool box will clear the vertical part of the rack.
AdminDeeZee2 –
We do not have a non mesh rack for the front.
AdminDeeZee2 –
No. The mounting is different from the front to rear racks.
AdminDeeZee2 –
The rear racks will not mount at the front. The front and rear racks have different mounting kits.
Terry Payne –
So lightweight and easy to put together with all other pieces
AdminDeeZee2 –
Unfortunately the non mesh do not fit properly at the front. We currently do not offer the non mesh for the front.
AdminDeeZee2 –
The rear racks do not fit properly at the front. The mounting plates are a little different. You will want to check the installation of the cover and the rack to make sure they will work together. The racks come in a texture black finish which is flat.
AdminDeeZee2 –
The non mesh racks do not work at the front of the bed. The mounting feet are different.
AdminDeeZee2 –
We do not have a riser block to do this.
AdminDeeZee2 –
The rear racks will not mount at the front. The mounting feet are a little different. We do offer light brackets.
AdminDeeZee2 –
The height of the rack is 23.158″.
AdminDeeZee2 –
The rear racks will not work at the front.
AdminDeeZee2 –
The rear racks do not mount at the front of the bed. The mounting brackets are not the same as the front racks.
AdminDeeZee2 –
It will not work with the cover. The mounting plates have a vertical lip that will not allow the cover and rack to work together.
AdminDeeZee2 –
The width of the plates for mounting are not same as at the front. This is due to most trucks are not straight from front to rear and we received complaints from customers how the plate hung too far over the side of the vehicle. So we have made the plates smaller and the width of the rack is shorter.
AdminDeeZee2 –
Not sure but probably not. If the cover uses the inside rail near the front of the bed for installation there may be interference with the way the rack installs.
AdminDeeZee2 –
The front and rear racks are the same height of 26.93″
AdminDeeZee2 –
The channel is on the top and bottom of the extrusion.
AdminDeeZee2 –
No the rear racks will not convert to fit at the front.
AdminDeeZee2 –
The rear racks will not work at the front. The mounting plates are just a little different.
AdminDeeZee2 –
All racks are mounted on the inside edge of the bed rail. For further information contact customer service. 800-779-2102
AdminDeeZee2 –
The height of the rack from bed rail to top cross bar is 23.158″.
AdminDeeZee2 –
DZ95054RB is the rear rack part number that will work on a 16 RAM 1500.
AdminDeeZee2 –
Unfortunately no. The mounting plates for the rears are different than the front.
AdminDeeZee2 –
The flange that is used to mount the plates on the inside of the rail will interfere with a tonneau cover.
AdminDeeZee2 –
It can probably be done. Not sure how to do that.
AdminDeeZee2 –
I have seen some installed. Do not know what brand of cover that was installed. We recommend looking at the racks instructions and the covers to determine if they will be compatible.
AdminDeeZee2 –
They do not. The mounting plates are different.
AdminDeeZee2 –
The non-mesh rear racks will not mount in the front. The mounting plates are a little different.
AdminDeeZee2 –
The rear racks will not work at the front. The mounting plates are not the same as the front mesh racks.
AdminDeeZee2 –
The non mesh will work at the front. The mounting is just a little different for each. With all the different covers on the market we do not know which ones do and do not specifically work with our rack.